Home > Support > Pyrotechnical Launcher Support > RG-46 Launcher Instructions
... < back 
RG-46 Insutructions

7 SHOTS, CAL. 6 MM (.22 CAL) ITEM #6051 BLANK CARTRIDGES ONLY

FUNCTIONING:
This launcher has a semi- automatic trigger-cocking mechanism. Pull trigger and cylinder operates automatically (double action system). Launcher can however also be cocked by hand (single action system). DO NOT PULL TRIGGER WITH EMPTY CYLINDER; THE CRIMPED BLANK CARTRIDGE SEATS AND THE FIRING PIN WILL BE DAMAGED.

SAFETY:
When cylinder is swung out or not fully snapped back the trigger mechanism is blocked. When the hammer is cocked, the cylinder cannot be swung out. The built-in automatic safety system prevents cartridges being fired inadvertently.

LOADING: (ONLY .22 CALIBRE BLANKS, TO BE USED WITH THIS LAUNCHER Item #6051)
Always point muzzle to the floor when loading crimped blanks. Push release on the left side of the frame forward (to disengage cylinder) and swing cylinder out to the left. Insert crimped blanks and swing cylinder back into original position.

FIRING: Dry Firing (with no blanks in chamber) will permanently damage launcher
Screw cartridge muzzle onto the barrel. Insert 15 mm pyrotechnical cartridge into the end of the muzzle as per instructions on pyrotechnic cartridge packaging, ie: BLACK or HOLLOW end in first. Fire at 45-degree angle above ground. When all seven crimped blanks are fired, it will be necessary to reload the cylinder.

REMOVING OF FIRED SHELLS:
Swing out cylinder as described above. When extractor (cylinder axle) is pushed backwards the seven shells are ejected simultaneously.

CLEANING:
After each use clean crimped blank chamber, muzzle adaptor and barrel with a 6mm bore brush and water. Dry all parts thoroughly after cleaning. Proper maintenance will increase the efficiency and life of the launcher. NB It is extremely important, that launcher & chamber be kept very clean, especially after heavy use, as it is possible for flash of blank to be impeded by carbon build up and flash backwards, igniting all blanks in chamber at once.

SAFETY INSTRUCTIONS:
• Operator must only fire this launcher in area clear of all personnel. Personnel should be a minimum of 5 meters behind launcher operator. Always fire at a 45-degree angle above the ground.
• Do not make any modifications to any components of this launcher.
• Never load or fire this launching device from a vehicle or vessel. Do not fire at humans, animals, buildings, and dry fields or at any flammable materials or liquids. Keep an adequate distance from all flammable objects.
• Always wear a hardhat, eye, and ear protection when using or handling this launching device.
• Never store launcher with crimped blanks or pyrotechnical cartridges inserted.
• This device is intended solely for the purpose of wildlife management and control. The proper and safe use of this device is the sole responsibility of the operator/owner. The seller assumes no responsibility or liability for the improper or illegal use, resale, physical injury or property damage resulting from the deliberate or accidental discharge, modifications to the device or cartridges, careless operation, and launcher maintenance neglect. The seller guarantees care in manufacture but assumes no further responsibility.
• Only mature, responsible adults who have a clear understanding of the functions of this device and a working knowledge of pyrotechnical scare cartridges and launchers should operate this tool. Persons under 18 years of age should not operate this device.
• Always keep this instructional sheet with the launcher.
• This launcher is not a firearm: it is a powder-actuated tool.
• Failure to comply with these safety instructions could result in serious injury or death.

IF UNCLEAR ON ANY OF THE ABOVE TOPICS, PLEASE CONTACT MARGO SUPPLIES LTD.
Phone: 403-652-1932 Fax: 403-652-3511 Email: info@margosupplies.com

Part Diagram

Diagram #

Ident. #

Description

 

Diagram #

Ident. #

Description

10

895339

Revolver Frame

 

260 *

881939

Cylinder Holder

50

678661

Cylinder Release

 

280

368443

Firing Pin Spring

60

680480

Countersunk Screw

 

290

678679

Cocking Lever

80a

687808

Left Handle Grip

 

350

671097

Release Screw

80b

698635

Right Handle Grip

 

360

385148

Pressure Shuttlecock

120

881935

Carrying Blade

 

450

678680

Hammer

140

678670

Security Lever

 

460

678697

Trigger

150

639196

Rest Blade

 

480

057092

Cylinder Latch Pin

200

005591

Pressure Spring

 

520

881944

Firing Pin

210

806286

Trigger Spring

 

530

684205

Firing Pin Shell

250

881942

Cylinder (complete)

 

560

324461

Pressure Spring

251

678681

Interlock Pin

 

570

057096

Security Lever Spring

252

678698

Cylinder Spring (large)

 

580

306649

Handle Grip Screw

253

678682

Cylinder Spring (small)

 

620

893450

Muzzle

254

678671

Washer

 

zu 10

012968

Frame Plate

255

678685

Extractor (cylinder axle)

 

 

010546

Cylinder Brush



  .. < back
. home