Home > Support > Pyrotechnical Launcher Support > RG-70 Launcher Instructions
... < back 
RG-70 Insutructions

6 Shots, .315 Cal. Blanks - (Item #6055) - Cartridges ONLY

FUNCTIONING:
This 6 shot launcher has a semi-automatic trigger cocking, clip advancing mechanism. AVOID PULLING THE TRIGGER (dry firing) WHEN THE MAGAZINE IS EMPTY.

LOADING:
Only .315 Cal. Blanks (Item #6055) may be used in this launcher. Rotate safety lever downward to the red dot. Press magazine catch backward - remove magazine. Fill magazine with cartridges and insert in launcher until magazine engages magazine catch. Now the launcher is preloaded. Pull slide all the way back and let it snap forward again – the launcher is now loaded. Swivel safety lever back to horizontal position – the safety is now off and the launcher is ready to fire.

FIRING: Dry Firing (with no blanks in the magazine), will permanently damage Launcher.
After loading, screw muzzle cup into launcher and insert 15mm pyrotechnical cartridge into the end of the muzzle as per instructions on pyrotechnic cartridge packaging, ie. BLACK or HOLLOW end in first. You are now ready to fire a 15mm pyrotechnical cartridge. Always fire at 45 degree angle from the ground. When all six blanks are fired, it will be necessary to reload the magazine.

CLEANING:

After each use launcher must be cleaned thoroughly. For that purpose, launcher must be dismantled into its three main components. To dismantle launcher for cleaning does not require any tools. Rotate safety lever downward to the red dot and remove magazine. Make sure the chamber is empty. Pull trigger guard downward, push it sideways with the index finger, and allow it to rest on the underside of the frame. Hold the trigger guard in this position with the index finger. Pull the slide fully back, then lift it off and allow slide to glide forward. Never allow the hammer to drop freely forward while launcher is party dismantled. Let hot water-jet flow through the chamber and the barrel. Clean chamber with enclosed bristle brush and barrel with any appropriate auxiliary material. Several drops of oil will keep launcher operating smoothly - wipe excess oil from launcher and reassemble. To reassemble, removing the recuperator spring - take care that afterwards its smaller end must be pushed first onto the barrel. Cock the hammer; pull the trigger guard down again. Allow it to rest on the underside of the frame and hold it in this position with the index finger. With the safety catch still “On”, replace the slide on the barrel at an oblique angle, pull it fully back and push it down flat on the frame. Then allow to slide forward. Pull the trigger guard down slightly and allow it to return to its normal position. Insert magazine.

SAFETY INSTRUCTIONS:

• Operator must only fire this launcher in area clear of all personnel. Personnel should be a minimum of 5 meters behind launcher operator. Always fire at a 45-degree angle above the ground.
• Do not make any modifications to any components of this launcher.
• Never load or fire this launching device from a vehicle or vessel. Do not fire at humans, animals, buildings, and dry fields or at any flammable materials or liquids. Keep an adequate distance from all flammable objects.
• Always wear a hardhat, eye, and ear protection when using or handling this launching device.
• Never store launcher with blanks or pyrotechnical cartridges inserted.
• This device is intended solely for the purpose of wildlife management and control. The proper and safe use of this device is the sole responsibility of the operator/owner. The seller assumes no responsibility or liability for the improper or illegal use, resale, physical injury or property damage resulting from the deliberate or accidental discharge, modifications to the device or cartridges, careless operation, and launcher maintenance neglect. The seller guarantees care in manufacture but assumes no further responsibility.
• Only mature, responsible adults who have a clear understanding of the functions of this device and a working knowledge of pyrotechnical scare cartridges and launchers should operate this tool. Persons under 18 years of age should not operate this device.
• Always keep this instructional sheet with the launcher.
• This launcher is not a firearm: it is a powder-actuated tool.
• Failure to comply with these safety instructions could result in serious injury or death.


IF UNCLEAR ON ANY OF THE ABOVE TOPICS, PLEASE CONTACT MARGO SUPPLIES LTD.
Phone: 403-652-1932 Fax: 403-652-3511 Email: info@margosupplies.com

Part Diagram

Diagram #

Ident. #

Description

 

Diagram #

Ident. #

Description

10

752867

784561

Pistol Frame - Blue

Pistol Frame - Nickel

 

241

752895

Hammer

242

303521

Hammer Lever

20

752869

784562

Slide - Blue

Slide - Nickel

 

243

093736

Cylinder Pin

244

752897

Cylinder Latch

30

752871

784563

Trigger Guard - Blue

Trigger Guard - Nickel

 

280

756016

Trigger Spring

290

752898

Trigger Pin

40

752873

Trigger

 

300

752899

Slide Spring

50

756589

Magazine Complete

 

310

752900

Firing Pin Spring

51

7528788

Magazine Shoe

 

320

303526

Cylinder Spring

52

729398

Magazine Stop

 

330

752901

Trigger Guard Spring

53

729398

Magazine Spring

 

340

752902

Hammer Spring

54

752876

Magazine Housing

 

350

000024

Slide Spring

55

752877

Feeder

 

390

747357

Cylinder Spring

80

756617

Handle Grip - (Pair)

 

400

303529

Cylinder Spring

100

303505

Magazine Stop

 

410

000032

Cylinder Spring

110

752882

Security Lever

 

420

733800

Cylinder Spring

130

303508

Slide Safety Lever

 

430

747358

 

150

752885

Trigger Lever

 

490

009055

Security Lever Stop

210

752892

Firing Pin

 

500

671097

Handle Grip Screw

230

752893

Trigger Latch

 

510

1028297

Muzzle Cup

240

752906

Hammer Complete

 

 

010546

Cylinder Brush



  .. < back
. home